Coated Garage Door Torsion Springs With Cones 7 & 8' High Doors
Our Made in U.S.A. High Quality Coated Torsion Springs are factory coated black for smoother, cleaner operation and also corrosion resistant and oil tempered for longer life.
For use on doors 7' or 8' high doors with 4" standard lift drums. Engineered for maximum application range. Minimum 10,000 cycles, at +/- 7.5 lbs of target door weight. Springs are made of steel coils with aluminum cones.
- Engineered For Maximum Application Range.
- Minimum 10,000 Cycles, At +/- 7.5lbs Of Target Door Weight.
- Springs Are Made Of Steel Coils With Aluminum Cones.
- Both Winding And Stationary Cones Are Installed.
- Black Coated, Oil Tempered Wire Provides A Clean Durable Finish.
- Clear, Easy To Read Spring Markings For Easy Identification.
- Top Quality Made In USA.
See Our Other Listings For Coated Garage Door Springs
Make sure you order the correct spring by comparing the information below with what you have.
Spring Length:
Measure your current spring (broken pieces included) from spring coil end to end - cones not included.
How to Determine if Torsion Spring is Left Hand or Right Hand Wound:
Standard springs are coded red and black. Red is right hand wind. Black is left hand wind. Always determine the wind of the wire.
To determine if you are ordering a right wind spring or left wind spring the easiest way would be check the coloring coding - if is it red or black.
Please note the side of door the spring is mounted DOES NOT indicate spring wind needed. Standard garage door systems have the right hand wound red winding cone on the end and will be mounted w/ the red winding cone pointing towards the LEFT. The left hand wound black winding cone will be mounted w/ the black winding cone pointing towards the RIGHT.

Left Hand Wind Right Hand Wind
1. Right hand wind would be wound counter clock wise in this diagram with the spring mounted on the left side of bracket.
2. Left hand wind would be wound clockwise in the diagram with the spring mounted on the right side of bracket.
After you've determined the the left & right hand winds you should have enough information to order.
Installation Instructions
|
To determine wire size measure 20 coils of wire and match with the chart below:
Length of 20 Coils
|
Wire Size
|
Length of 20 Coils
|
Wire Size |
2 1/2"
|
.125 |
5 3/4"
|
.289
|
2 3/4"
|
.135
|
5 7/8"
|
.295 |
2 7/8"
|
.142 |
6 1/8"
|
.3065 |
3" |
.1483 |
6 1/4"
|
.3125 |
3 1/8"
|
.1562 |
6 3/8"
|
.3195 |
3 1/4"
|
.162 |
6 5/8"
|
.331 |
3 3/8"
|
.170 |
6 7/8"
|
.3437 |
3 1/2"
|
.177 |
7 1/4"
|
.3625 |
3 3/4"
|
.1875 |
7 1/2"
|
.375 |
3 7/8"
|
.192 |
7 7/8"
|
.3938 |
4 1/8"
|
.207 |
8 1/8"
|
.4062 |
4 3/8"
|
.218 |
8 7/16"
|
.4218 |
4 1/2"
|
.2253 |
8 5/8"
|
.4305 |
4 5/8"
|
.2343 |
8 3/4"
|
.4375 |
4 7/8"
|
.2437 |
9 1/16"
|
.4531 |
5" |
.250 |
9 1/4"
|
.4615 |
5 1/4"
|
.2625 |
9 3/8"
|
.4687 |
5 1/2"
|
.273 |
9 3/4"
|
.490 |
5 5/8"
|
.283 |
10" |
.50 |
|
WARNING - Garage door springs, cables, brackets, and other hardware attached to the springs are under very high tension and, if handled improperly, can cause serious injury. Only a qualified professional or a mechanically experienced person should adjust them, but only by carefully following the manufacturer's instructions.